head_bg

Wholesale China Di Resin Filter Manufacturers Suppliers - MA-202U (Macroporous Strong-Base Anion Exchange Resin) – Dongli

Wholesale China Di Resin Filter Manufacturers Suppliers - MA-202U (Macroporous Strong-Base Anion Exchange Resin) – Dongli


Product Detail

Product Tags

Related Video

Feedback (2)

We've been convinced that with joint efforts, the enterprise between us will bring us mutual benefits. We are able to assure you product or service quality and aggressive cost for Nitrate Selective Resin , High Capacity Resin , Gel Type Anion Resin , As a result of our hard perform, we have always been around the forefront of clean technology merchandise innovation. We've been a eco-friendly partner you can rely on. Get hold of us today for additional data!
Wholesale China Di Resin Filter Manufacturers Suppliers - MA-202U (Macroporous Strong-Base Anion Exchange Resin) – Dongli Detail:

Uranium is radionuclide ,more likely to occur in ground water than surface water, and is often

found together with radium. Mitigation of problem waters may require treatment for the removal of both uranium and radium.

Uranium typically exists in water as the uranyl ion, UO22+, formed in the presence of oxygen. At pH above six, uranium exists in potable water primarily as the uranyl carbonate complex. This form of uranium has a tremendous affinity for strong base anion resins.

The relative order of affinity of strong base anion resins for some common ions in drinking water show uranium at the top of the list:

Typical physical & Chemical characteristics

 Polymer Matrix Structure   Styrene Crosslinked with DVB
 Physical Form  and Appearance   Opaque beads
 Whole Bead Count   95% min.
 Functional Groups  CN2-N+=(CH3)3)
 Ionic Form ,as shipped   SO4
Total Exchange Capacity, SO4- form, wet, volumetric    1.10 eq/l min.
Moisture Retention, CL- form   50-60%
   0.71-1.60 mm >95%
Swelling CL-→ OH-  10% max
 Strength  Not less than 95%

Regeneration

In order to regenerate the uranyl carbonate it is important that the concentration of the regenerant at the resin bed be sufficiently high to reverse or reduce the relative affinities to acceptable levels and to use enough regenerant and contact time. Sodium chloride is the most common regenerant.

Concentration above 10% NaCl, at regenerant levels of 14 to 15 lbs. per cu. ft. is sufficient to insure better than 90% uranium removal through the operating cycle. This dosage will elute at least 50% of the collected uranium from the resin. Leakage will remain low through the service cycles even without complete regeneration because of the very high selectivity during the service cycle. Leakages are essentially nil for regeneration levels of 15 lbs. of sodium chloride per cu. ft. at concentrations of 10% or higher with minimum contact time of at least 10 minutes during regeneration.

Effectiveness of varying concentrations of salt:

Regenerant Level – Approximately 22 lbs. per cu. ft. of Type 1 Gel Anion Resin.

NaCl Concentrations

4%
5.5%
11%
16%
20%

Uranium Removed

47%
54%
75%
86%
91%

Safety and Handling

Regenerant waste from the uranium removal system is a concentrated form of the uranium and must be disposed of properly. For the homeowner, the spent solution is usually discharged the same way softener brine is discharged, the net amount of uranium reaching the disposal point is the same whether or not a uranium removal unit is in place. Still, it is necessary to check the regulations for a given locale.

Disposal of uranium-laden resin must take into account the amount of radioactivity present in the media.

The U.S. Department of Transportation regulates the transportation and handling of low level radioactive waste. Uranium is less toxic and so has higher allowable levels than radium. The reported level for uranium is 2,000 picoCuries per gram of media.

Anticipated throughputs can be calculated by your ion exchange resin supplier. Once-through applications can reach theoretical throughput volumes much greater than 100,000 bed volumes (BV), while service cycles on regenerable service can be around 40,000 to 50,000 BV. Although it is tempting to run the resin as long as possible on the once-through applications, consideration must be given to the total amount of uranium collected and the subsequent disposal issues.


Product detail pictures:


Related Product Guide:

Our organization insists all along the quality policy of "product quality is base of business survival; purchaser gratification is the staring point and ending of an business; persistent improvement is eternal pursuit of staff" as well as the consistent purpose of "reputation 1st, purchaser first" for Wholesale China Di Resin Filter Manufacturers Suppliers - MA-202U (Macroporous Strong-Base Anion Exchange Resin) – Dongli , The product will supply to all over the world, such as: Philippines, Belgium, Madagascar, Our advantages are our innovation, flexibility and reliability which have been built during last 20 years. We focus on providing service for our clients as a key element in strengthening our long-term relationships. The continual availability of high grade products in combination with our excellent pre- and after-sales service ensures strong competitiveness in an increasingly globalized market.
It is a very good, very rare business partners, looking forward to the next more perfect cooperation!
5 Stars By Honorio from Afghanistan - 2018.09.19 18:37
The factory workers have a good team spirit, so we received high quality products fast, in addition, the price is also appropriate, this is a very good and reliable Chinese manufacturers.
5 Stars By Cheryl from Mauritania - 2017.09.29 11:19
Write your message here and send it to us